Language
TRENARRU

+90 554 843 46 56 · yasin@brborline.com

PPRC Pipe Dimensions and Pressure Classes

Wall thickness, inner diameter and the S / SDR / PN relationship for Ø20–Ø110 mm PPRC pipes: a reference chart based on the DIN 8077 and ISO 15874-2 metric series.

Last reviewed: 21 Nov 2026

What do S, SDR and PN mean?

PPRC pipes are defined by outside diameter (d) and wall thickness (e). SDR (standard dimension ratio) is the ratio of outside diameter to wall thickness: SDR = d / e. The pipe series S follows from S = (SDR − 1) / 2. All diameters with the same SDR have the same internal pressure resistance; the wall grows in proportion to the diameter.

PN (nominal pressure) is a trade class in bar for water at 20 °C. The PN label depends on the safety factor chosen and can differ between manufacturers: some catalogues mark an SDR 7.4 pipe as PN16, others as PN20. Always state the S or SDR value next to PN in orders and project documents.

Wall thickness and inner diameter chart (Ø20–Ø110)

Table 1 – PPRC pipe nominal wall thickness e and calculated inner diameter di in mm (cells: e / di). PN labels follow the common pairing in DIN 8077 catalogues.
Outside diameter d (mm)Approx. inchS5 · SDR 11
PN10
S3.2 · SDR 7.4
PN16
S2.5 · SDR 6
PN20
S2 · SDR 5
PN25
201/2"1.9 / 16.22.8 / 14.43.4 / 13.24.1 / 11.8
253/4"2.3 / 20.43.5 / 18.04.2 / 16.65.1 / 14.8
321"2.9 / 26.24.4 / 23.25.4 / 21.26.5 / 19.0
401 1/4"3.7 / 32.65.5 / 29.06.7 / 26.68.1 / 23.8
501 1/2"4.6 / 40.86.9 / 36.28.3 / 33.410.1 / 29.8
632"5.8 / 51.48.6 / 45.810.5 / 42.012.7 / 37.6
752 1/2"6.8 / 61.410.3 / 54.412.5 / 50.015.1 / 44.8
903"8.2 / 73.612.3 / 65.415.0 / 60.018.1 / 53.8
1104"10.0 / 90.015.1 / 79.818.3 / 73.422.1 / 65.8
  • di = d − 2e, calculated from nominal values without tolerances.
  • Some manufacturers list 2.0 mm wall thickness for Ø20 SDR 11.
  • Some manufacturers supply the PN25 class as a glass-fibre reinforced composite pipe instead of solid-wall SDR 5; dimensions then follow the manufacturer catalogue.
  • Inch equivalents are approximate trade equivalents; PPRC pipes are sized by metric outside diameter.

Typical fields of application

Table 2 – Typical application pairing from a manufacturer manual (Wavin).
Pipe seriesTypical use
S5 · SDR 11Cold water and floor heating
S3.2 · SDR 7.4Hot water and floor heating
S2.5 · SDR 6Hot water and central heating

Choosing the pipe series by application class

ISO 15874 groups PPRC systems into application classes by service temperature profile, with a 50-year design life. The table shows the pipe series required for 8 bar and 10 bar operating pressure.

Table 3 – Pipe series required per ISO 15874 application class (Uplast technical catalogue, Table 6).
Application classUse8 bar10 bar
1Hot water supply 60 °CS3.2 · SDR 7.4S2.5 · SDR 6
2Hot water supply 70 °CS2.5 · SDR 6S2 · SDR 5
4Floor heating and low-temperature radiatorsS3.2 · SDR 7.4S3.2 · SDR 7.4
5High-temperature radiatorsS2 · SDR 5—

Quick selection notes

  • Assess pressure and temperature together: the permissible operating pressure falls as temperature rises.
  • Pipes of different SDR share the same outside diameter, so they weld to the same socket fittings.
  • Thermal elongation is significant on hot water lines; see the installation guide for the expansion calculation. Installation guide

Sources

Values were compiled from published documents based on the standards below and cross-checked against each other. Full standard texts are paid, so manufacturer catalogues declaring conformity to them were also used.

  1. DIN 8077:2008-09 – polypropylene pipes, dimensions (table of contents, DIN)
  2. Peštan – Technical catalogue, pipes and fittings DN16–630 (tube geometry table, expansion coefficient, support spacing)
  3. Uplast – PPRC pipe and fitting systems technical catalogue (wall thickness table S5–S2, application classes)
  4. Wavin – Pilsa piping systems technical and installation manual (support spacing, expansion, pressure test)

This page is for information only. The project specification, local regulations and the instructions of the pipe and fitting manufacturer always take precedence.

More technical pages

BORLINE PPRC pipes and fittings – Share sizes, SDR and packing needs for your export order and we will prepare a product list and quotation.

Get in Touch

Write to us about products, prices or dealership.